RespSense^® II Specifications

Capnography Specifications

Respiration Range: 0 to 99 respirations/minute
Respiration Accuracy^{1, 2}:
3 to 50 respirations/min ± 2
51 to 60 respirations/min ± 3

Test method summary: To determine the rated respiration rate, calibrated CO₂ gas tanks are used as the respiration rate is changed from 3 to 60 BrPM.

EtCO₂/CO₂ Range: 0 to 99 mmHg (0 to 13.2 kPa)
EtCO₂/CO₂ Accuracy:
±0.2 kPa / ±2 mmHg, +8% of reading³
525 – 795 mmHg (700 – 1060 hPA)
(EtCO₂/CO₂ reading reaches its steady state accuracy within 10 minutes after power up. From maximum storage temperature, monitor reaches steady state accuracy 19 minutes after power up.)

Calculated Update Frequency: Once every breath (“NO BREATH” alarm after 30 seconds)
Sampling Rate: 4 Hz (4 times per second)
Total System Response Time: <7 seconds (includes delay time and rise time)
Drift of Measurement: Within CO₂ accuracy specifications for 6 hours of continuous monitoring
Measurement: Automatic barometric pressure compensation and CO₂ temperature compensation

¹ There is no known adverse effect on performance due to cyclical pressure up to 10 kPa.
² There is no degradation in EtCO₂ measurement accuracy as a function of BrPM and inspiratory/expiratory (I/E) time ratio.
³ Presented concentration of CO₂ and EtCO₂ can be false, indicating a high presence of nitrous oxide and other interfering gases.

The table below shows the CO₂ and EtCO₂ concentration corrections. Only use agents listed in the table below.

System Specifications

Power Data:
Power Supply: 100 – 240 VAC 50 – 60 Hz
Power Consumption:
3.6 W with battery operation
9 W with power supply
Input: 12 VDC, 1.5 A

Internal Battery:
Type: Lithium Ion (Li-Ion) internal battery, non-field replaceable, rechargeable
Battery Capacity: Approximately 5 hours
Charging Time: Approximately 9 hours

Dimensions: 200 x 135 x 50 mm (7.9 x 5.3 x 2 in.)
Weight: 865 grams (1.9 pounds)
Memory: 36 hours (assuming continuous operation)
Temperature:
Operating: 0 to 40 °C (32 to 104 °F)
Storage/Transportation: -40 to 70 °C (-40 to 158 °F)
Time (from storage) for monitor to be ready for its intended use:
10 minutes to warm from -40 to 0 °C
19 minutes to cool from 70 to 40 °C

Applied part temperature will not exceed 41°C as measured during a controlled environment test.

Humidity:
Operating: 15% to 93% noncondensing
Storage/Transportation: Up to 93% noncondensing

Altitude:
Operating: Up to 2,740 meters (9,000 feet)
Atmospheric Pressure: 525 to 795 mmHg (700 to 1060 hPa)

Pump:
Pump Flow: 75 ml/min (minimum sample flow rate: 60 ml/min)
Flow Accuracy: ±15 ml/min

High and Medium Priority Alarms (at 1 m):
Sound Pressure Level: 74.6 to 75.5 dB

Classification per ANSI/AAMI ES60601-1 and CAN/CSA-C22.2 No. 60601-1:
Type of Protection: Internally powered class II (with power supply)
Degree of Protection: Type BF-Applied Part
Mode of Operation: Continuous
Enclosure Degree of Ingress Protection: IP22